Quartz SIMPLEX 500 Especificações

QUARTZ TIME RECORDEROPERATION MANUALSimplex 500

To prepare for setting:5. SETTINGPreparation for setting1 Unlock the unit. While holding down the panel, open buttons at both sides of the unit and l

DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELECTYEARRED/BLK.MONTHEX.ALMDAYCOL.HOUR MINUTE SECOND/CARDDATE/TIMESU 12Hr. TU SAFRTHWEMO1/601/100S

1 Remove the panel cover.Make sure that the PAY ENDING button stays lit up.2 Press or to cause the digits at the right to flash ("0

1 Remove the panel cover.Make sure that the PAY ENDING stays lit up.2 Press or to cause the digits at the right to flash "00".

Setting the Date and the Time, 1/60 or 1/100 printing, andthe 12/24 HOUR formatThe DATE/TIME button stays lit up during its setting operation.1 Press

4 Setting for 1/60 or 1/100 printingPress or to cause the digits at the upper left to flash.Press or to select the printing between

Setting the Day Advance TimeThe day advance time refers to the time when printing shifts to the next line on a time card for the next day. This funct

Setting the Daylight Saving Time (D.S.T.)Daylight saving time function 1 D.S.T. execution timeAt 2:00 a.m. on the first day of summer time, the cloc

• Daylight saving time is not pre-set at the factory (with the indication of month 00 and day 00).• The D.S.T. button stays lit up during its s

DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELECTYEARRED/BLK.MONTHEX.ALMDAYCOL.HOUR MINUTE SECOND/CARDDATE/TIMESU 12Hr. TU SAFRTHWEMO1/601/1003

The details of this Operation Manual are subject to change without previous notification.This Operation Manual has been prepared with the utmost care

Setting the Time Table ProgramThe time table program function allows automatic selection of print color (black or red), an external time signal, and

Follow these steps to set time table programs.1 Press SELECT to cause the PROGRAM button light up.DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSEL

2 To set P-01 (shown in the table above)(1) Print colorWith "P-01" flashing, press once. The print color indication flashes at the lo

Press again. The minute indication flashes. Leave the digits as they are since the desired time is 05:00 in this case.(5)Day of the weekPress

DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELECTYEARRED/BLK.MONTHEX.ALMDAYCOL.HOUR MINUTE SECOND/CARDDATE/TIMESU 12Hr. TU SAFRTHWEMO1/601/100D

4 To set P-03Make settings as shown in the figure at left, and press SET .5 To set P-04Make settings as shown in the figure at left, and press SET .

To check program settingsPress SELECT to cause PROGRAM to light up. Make the desired program No. flash. To see program settings, press .The

3 Check the settings on the display and press SET .Setting Number of Seconds for External Time Signal1 Press SELECT to cause EXT. ALARM to light up. 2

ResettingTo restore all the settings to factory-shipped state, push the reset switch with a pointed object.Be careful! Resetting will erase all the s

Follow the steps below to connect to an external time signal device.6. CONNECTING TO AN EXTERNAL TIME SIGNAL 3 Replace the lid after pulling the wires

TABLE OF CONTENTSPRECAUTIONSFEATURESBEFORE USING THE TIME RECORDERAccessoriesFeaturesInstalling the Ribbon CassetteWall MountingEnvironmental Conditio

7. INST ALLING THE Ni-Cd BA T TERY (OPTIONAL)Follow the steps below to install a Ni-Cd battery (optional) in case of power failure.3 Hook the lid to c

9. SPECIFICATIONSClock displayCalendarPrinting systemCard mechanismDimensionsWeightPower supplyPower consumptionPower failure compensationPrint at pow

Front Side Reverse Side1 210. TIME CARD SPECIFICA TIONS(1) Monthly CardNote : Recommended paper thickness : 0.45 ± 0.05mmNote : Card style may vary.

(2) Weekly Card (3) Bi-Weekly Card32

Printed in Japan1406-980610-10B01S

1. PRECAUTIONSSignsVarious warnings and cautions are provided throughout this manual along with signs. Remember each sign and its explanation listed

2. FEATURESThe time table program provides the following functions:•Automatic switching between black and red printingThe two-color printing system ma

Features<Display><Front view> <Back view>Daylight saving time indicationCurrent dateSU MO TU WE TH FR

Panel coverInstalling the Ribbon Cassette1 Unlock the unit. While holding down the panel, open buttons at both sides of the unit, and lift the panel

Wall MountingThe unit can be mounted on a wall using the supplied mounting fittings. To mount the unit on a wall, take the following steps:The suppli

Once the AC line cord is plugged into the outlet, the unit can be used immediately as basic operation has been pre-set at the factory, including the t